1. Semi-automatic and manual punches must be equipped with a two-hand brake switch. It is strictly prohibited to start the switch stamping with a foot or one hand. 2. After the high-impact machine is adjusted, after normal punching, close the soundproof box (except for the product 8065 packaging during inspection). 3. During continuous punching, employees cannot pick up the product by hand within 1M of the punch. 4. When the technician is on the machine, only one person can debug, not two people. 5. The technician adjusts and feeds the material, only outside the machine, and the distance is not less than 1M. 6. Be sure to tighten the screws when mounting the mold, and stop after 4 hours to check whether the screws are loose. 7. When there is a problem in the production process of the mold without removing the mold, and directly repairing on the machine tool, you must first turn off the power of the injection molding machine and hang a maintenance sign on the power box before performing the mold repair. 8. All tools will be returned to the tool box after they are used up. Do not put them on the machine to prevent the tools from falling and hurting people. 9. When the machine is not in production, cut off the power supply in time. 10. For short workpieces, special tools must be used. Do not directly feed or pick up parts by hand. 11. The producer should stand properly, keep a certain distance between the hand and head and the punch, and pay attention to the punch movement at all times. It is strictly forbidden to chat with others. 12. It is strictly forbidden for operators and mold repairers to put their hands into the mold during production. 13. When the operator installs the suction fan, it is strictly forbidden to put his hand on the motor to clean the waste. 14. It is strictly forbidden to wear slippers when going to work, so as not to hit the feet with molds and iron blocks in the workshop. The squad leader, fitter, and mold repairer must wear protective shoes when they go to work; 15. Male operators are strictly forbidden to leave long hair, and female operators must keep their hair up to prevent long hair from getting caught in the flywheel. 16. Pay attention to fire prevention for white oil, alcohol, cleaning agent and other oils. 17. Wear gloves when packing materials, scraps and molds to avoid scratching your hands. 18. If there is oil, clean it up in time to avoid slipping. 19. It is strictly forbidden to wear gloves when drilling and milling; wear a mask and eye protection when using the grinding machine to protect yourself. 20. Be careful to drag the mold to prevent it from falling to the ground (the flatbed cart must be lowered to the minimum to pull the mold). 21. It is strictly forbidden for non-electricians to connect electricity and repair the machine. 22. It is strictly forbidden to blow the wind gun at people, which may hurt the eyes. 23. The operator needs to wear earplugs. 24. When the machine is found to be abnormal, turn off the power first and then ask the technician on duty to handle it in time. 25. When a new employee comes to work on the first day, the team leader must explain to him good safety practices and study the safety practices once a day for the first week. 26. When adjusting the machine, be sure to adjust the machine to a single action. 27. Do not store any flammable or explosive items under the switch. 28. Operators are strictly prohibited from chasing and chasing in the workshop to avoid falling, hitting the product or hurting themselves. 29. Carry out equipment inspection according to the inspection content on the equipment inspection card. Pay special attention to whether the guide and braking device of the punch are operating normally. The single and continuous punch functions are clear. 30. When installing the mold on the small punch (10T), first loosen the locking device of the guide rail, install the upper and lower molds, and then adjust the stroke of the guide rail until the requirements are met and the fastening device is locked. Hit the single-stroke stroke, after the upper mold is locked, the lower mold is locked after hydraulic clamping, and a check is made before production. · 31. Special tools (pliers, hooks) must be used when discharging or manually feeding blanks. It is strictly prohibited to send or remove blanks by hand. A single switch will hurt your hand and a double switch. The machine must not leak oil, otherwise it will fall down. Do not expose the power supply. It is dangerous. 32. Wear gloves and concentrate when punching iron pieces, otherwise your hands will be injured. 33. During work, first check the equipment for abnormal operation, such as unclear single, continuous charging, poor operation or electrical failure, immediately stop the machine in time to find a technician on duty to deal with it. 34. It is strictly forbidden to use the foot switch for the punch press, and all the original equipment is dismantled. 35. When cleaning and inspecting the equipment, the power must be cut off before operation. 36. Turn off the power, clean and scrub the work surface, remove the mold for maintenance and storage, and check the lubrication system oil at a certain time every week.